.
Plasters, Block Adhesives and Putty

SAMWAL® PL  

Ready Mix Polymer Plaster

SAMWAL® PL is a ready-to-use dry powder requiring only the addition of water. It produces a high strength mortar with non-shrinking property. The material is a mixture of specially processed cement and carefully graded fine aggregates. Additives impart high water retaining properties and adhesion to substrate. The very low water / cement ratio ensures high early and ultimate strengths.

Packing

25 kg bag (HDPE)

 

Form

Powder

 

Base

Cement

 

Color

Grey

 

Safety

Non-toxic

• Clean the base by removing dust, loose particles grease, paint and traces of foreign materials.
• Dampen dry concrete / rendered surfaces where-ever necessary before application of SAMWAL® PL.
• Add SAMWAL® PL to mixing bucket containing clean potable water.
• Mix until an even homogenous mortar is obtained and keep the mixture as it is for 10 minutes for additives to dissolve.
• Mix again and paste is ready to use.
• Trowel firmly into all edges first and over the entire area.
SAMWAL® PL must be cured immediately as soon as the surface slightly stiffens for a minimum period of 72 hours.
• It gives very high strength; nearly three times more than the normal mortar.
• Ensures effective bonding and eliminates shrinkage problems associated with conventional cement concrete / mortars.
• Provides a uniform micro-cellular material structure and smooth dust-free finish.
• No metallic iron content to corrode and cause staining or deterioration due to rust expansion.
• Plastering interior / exterior walls and ceiling.
• Patching and repairing of work areas.
• Filling of holes or depressions in concrete floor slabs of factories, godowns, commercial or domestic
buildings etc.
Samfix Front-resized
Samfix Back-resized
previous arrow
next arrow
Samfix Front-resized
Samfix Back-resized
previous arrow
next arrow
Plasters, Block Adhesives and Putty

SAMFIX®

High Bond Block Joint Mortar

SAMFIX®  is a ready-to-use dry powder, requiring only the addition of water. It produces a high-bond strength mortar with non-shrinking property. SAMFIX® is made up of specially processed cement, carefully graded fine aggregate and special additives. This unique combination enables it to be more compact, thinner and more versatile to impart more durable bond between the blocks with superior adhesive strength.

Packing

40 kg (HDPE bag)

 

Form

Powder

 

Base

Cement

 

Color

Grey

 

Safety

Use mask and hang gloves.

• The masonry units should be clean, with no loose particles or dust for better bonding. Surface of the masonry units should be slightly wet prior to application.
• Mix SAMFIX®  with recommended qty of water with a mechanical mixer.
• Mix until an even consistent mortar is obtained.
• Apply uniform layer of 3-4mm thick SAMFIX®  on the clean and levelled surface of masonry units using proper trowel.
• Place the next course of masonry units on the evenly laid jointing mortar bed in proper line and level. Each masonry unit should be properly embedded and set in position by gently pressing with the handle of a trowel.
• After placing the first unit, apply SAMFIX®  in same thickness on both the sides of the unit, keeping continuous check of line and level.
• Clean the excess material, if any, immediately. Continue the process for the entire masonry work.
• Though it is a thinner jointing mortar, SAMFIX® gives nearly three times more bond-strength than the
conventional cement mortar.
• Ensures effective bonding and eliminates shrinkage problems associated with conventional cement mortars.
• Provides a uniform micro-cellular material structure and smooth dust-free finish.
• Eliminates lengthy process of site mixing, transport and storage of all individual materials.
• Economical and consumption is far less than conventional mortar.
• For laying and jointing of masonry units like fly ash bricks, concrete blocks, hollow blocks, AAC blocks etc.
• Jointing of pre-stressed concrete slabs, panels
• Jointing of concrete window and door frames.