.
SAMBOND® CF is a one component (Ready to use), flexible crack filling compound recommended for repair in concrete.
SILICON IMPREGNATION-S-4 is an optimal constructed impregnation for facades with extremely high alkali-resistance and long time duration. It is a solvent-containing, one-component impregnation based on oligomer siloxane.
Advantages :
➤Fresh concrete can be treated even 24 hours after dismantling of form work, but it should be regarded that the penetration-depth of SILICON IMPREGNATION-S-4 gets higher with the dryness of substrate
➤Cracks and tears with a size above 0.3 mm must be leveled out before treating
➤Old facades must be cleaned of moss, braids and dirt
➤Prefabricated parts as well as building blocks or roof-tiles can be impregnated by brush, spray or immersion
➤Concrete can be impregnated even 24 hours after dismantling of the form-work
Method of Use :
➤SILICON IMPREGNATION-S-4 is best applied by spraying
➤Substrate shall be dry
➤The mouth of the spraying gun is to hold approximately 10 cm in front of the façades and let it there while spraying as long as the solution is no longer absorbed by the façades and is running down
➤By taking a low spraying-pressure the atomization of the solution can be prevented
➤Smaller areas can also be treated with a brush
➤Processing temperature to be kept above +5°C air-and substrate-temperature
Recommended Applications :
➤Exposed concrete, exposed aggregate concrete, gas-concrete, fresh asbestos cement, natural stones, artificial stones, all sorts of mineral plaster, faced brickwork, clinker
➤As a primer for cement paint, artificial resin paint and dispersion paint
SAMSEAL-4-S is a high performance roofing and waterproofing membrane, comprised of a non woven polyester fleece, which is thoroughly impregnated and coated with APP, and modified bitumen. The synthetic modified coating is homogeneous mixture of a special bitumen and a high-quality APP polymer, which gives the membrane high durability. Production processing and factory control are certified according to EN ISO 9001:2000.
Advantages :
➤Enormous resistance against UV and thermal ageing
➤Life-long durability
➤Shows a very good resistance against mechanical damage
Method of Use :
➤SAMSEAL-4-S is used as cap-sheet at roofs for new-building projects as well as for reconstruction
SAMPRIME-LF is a high quality, artificial resin dispersion used as sealant for waterproofing of absorbent substrates having excellent penetration properties.
Advantages :
➤Excellent penetration in surface and provides superb bonding between base substrate and waterproof coating
➤Coating film is thin but flexible with excellent adhesion to concrete, cementitious mortar and cement screed
➤It eliminates porous in concrete surface
➤Highly ideal for alkaline concrete and saline environment
Method of Use :
➤Dries on absorbent substrates within 15 minutes
➤It takes only 12 hours to dry on non-absorbent substrates
Recommended Applications :
➤For strong bonding between surface of concrete and waterproof coating
➤For better sealing of concrete screed surface
➤Not recommended for wood, plastic metal, paint
SAMPLAST®-LW is an integral cement water proofing liquid admixture with BIS-Certification Mark
Advantages :
➤Ideal for use as an integral waterproofing compound with both general mass concrete work as well as mortars
➤Easy to use and ensures instant-uniform dispersion due to its liquid form
➤Increases workability of concrete and mortars
➤Reduces water bleeding
➤Effective with most types of cements including pozzolonic cements except for high alumina cement
➤Reduces the hydraulic permeability of concrete and mortars up to 90% and thereby enhances its life by 10 to 15 years
Method of Use :
➤Add SAMPLAST®-LW (100 gm per 50 kg of cement) in water and stir gently
➤Prepare dry mix of cement, sand and aggregates
➤Add the dry mix to SAMPLAST®-LW solution while mixing
➤Use concrete/mortar mix as usual
Recommended Applications :
➤RCC water tanks and storage reservoir
➤External plastering & masonry walls
➤Roof and balcony areas
➤Plastering of basements and water tanks
➤Floor and roof slabs
➤Small machinery foundations
➤Small bund / check dam walls
➤Not recommended for use with structural members like beams and columns and some pre-cast elements particularly where high cement contents are required
SAMPLAST®-PW is a BIS-Certified admixture in powder form to reduce porosity in concrete or mortar matrix.
Advantages :
➤Improves workability
➤High quality waterproofing material
➤Low permeability (13.95%) to water
Method of Use :
➤Add SAMPLAST®-PW into dry cement in the ratio of 1 packet (0.500 kg) per one bag of cement (50 kg)
➤Mix properly to make uniform mixture
➤Add this mixture to the sand / concrete mixer
➤Mix thoroughly and use the mix as usual
Recommended Applications :
➤RCC water tanks and storage reservoirs
➤External plastering and masonry walls
➤Roof and balcony areas
➤Plastering of basements and water tanks
➤Floor and roof slabs
➤Small machinery foundations
➤Small bund / check-dam walls
➤Not recommended for use with structural members like beams and columns and some pre-cast elements particularly with high cement contents
SAMBOND®-CCF is a two-component, Acrylic-modified cementitious coating product which forms a tough, elastomeric film. It is ideal for all types of structures including those in coastal environments and is also most effective on concrete; brick and block work substrates and is equally suitable for new and existing structures. The product is designed to bridge shrinkage cracks and to provide a seamless, flexible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements and roofs. SAMBOND-CCF also provides a tough durable water resistant coating which can withstand light pedestrian traffic and also has excellent weather resistance for exterior applications.
Advantages :
➤Provides quite efficient protection to concrete
➤Impermeable to water (without pressure) (prevent penetration of water) but at the same time permeable to water vapor
➤Suppresses carbonation
➤Hinders chloride penetration
➤High resistance to the effect of long-term weathering
➤Durable in all climate conditions including UV attack
➤Non toxic and ideal for potable water tanks
➤Flexible with thermal expansion similar to concrete
➤Excellent bond to concrete and masonry works
➤Good crack-bridging capacity
➤Minimum surface preparation needed and as such incurs low labor costs
Method of Use :
➤Pour SAMBOND®-CCF Part 1 into a bucket
➤Start stirring and slowly add SAMBOND®-CCF Part 2 avoiding any lump formation
➤Mix for 2/4 minutes
➤Apply 2 coats of the prepared mix on the substrate surface
➤Keep 2-6 hours interval in between 2 coats
➤Apply with brush
Recommended Applications :
➤Damp proofing of houses
➤Waterproof repairing
➤Walls, terraces and bridges to provide damp proofing
➤To fill holes, cracks, imperfections, honey comb, rough and defective areas in concrete
SAMBOND®-CC-1 is a one component, Acrylic-modified coating which forms a tough, rubbery film. It bridges cracks, and is ideal for repairing works.
Advantages :
➤Provides quite effective protection to concrete
➤Impermeable to water (without pressure) (prevent penetration of water) but at the same time permeable to water vapor
➤Suppresses carbonation
➤Hinders chloride penetration
➤Resistant to thermal & ultra violet ageing
Method of Use :
➤After wetting of surface, apply 3 coats of SAMBOND®-CC-1
➤For 1st coat only add water half the quantity of SAMBOND®-CC-1
➤Keep 2-6 hours interval in between 2 coats
➤Apply 2nd and 3rd coat without adding water
➤Apply with brush
Recommended Applications :
➤Damp proofing of houses
➤Waterproofing
➤Walls, terraces and bridges to provide damp proofing
➤Sealing holes, cracks, imperfections, honeycomb, rough and defective areas in concrete
SAMBOND®-CC is an acrylic polymer-modified cementitious coating admixture available in two components.
Advantages :
➤Provides a protective waterproof coating
➤Resists water pressure up to 7 meters overhead
➤Can be applied directly to concrete and masonry works with minimum surface preparation
➤Provides high resistance to carbon dioxide and chloride ion diffusion
Method of Use :
➤Pour SAMBOND®-CC Part 1 into a bucket
➤Add required volume of clean water and start stirring
➤Slowly add SAMBOND®-CC Part 2 avoiding any lump formation
➤Mix for 2/4 minutes
➤Apply the prepared mix on the substrate surface
Recommended Applications :
➤Water tanks, reservoirs and sealing tie bar holes to ensure water tightness
➤Walls and bridges to provide damp proofing
➤Sealing holes, cracks, imperfections, honeycomb, rough and defective areas in concrete structures